Deploy
standalone Access point
AP
nowadays come with Controller(WLC) based IOS, however that is possible to
convert the access point to standalone access point (save $)
CAP-2602I
Controller
based AP.
LAP-1042
Lightweight
Access point
Using a TFTP Server to Return to
a Previous Release
Note 
This
section does not apply to Cisco C3201WMIC and Cisco C3201LAP.
Follow
these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS
release using a TFTP server:
Step
1 
The
static IP address of the PC on which your TFTP server software runs should be
between 10.0.0.2 and 10.0.0.30.
Step
2 Make
sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for
a 1200 series access point) in the TFTP server folder and that the TFTP server
is activated.
Step
3 Set the
timeout value on the TFTP server to 30 seconds.
Step
4 On the
PC where the TFTP server is located, perform these steps:
a. 
Disable
any software firewall products, such as Windows firewall, ZoneAlarm firewall,
McAffee firewall, or others.
b. Ensure
all Windows files are visible. From Windows Explorer, clickTools
> Folder Options > View; then uncheck the Hide
extensions for known file types check box.
Step
5 Rename
the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a
1200 series access point, c1130-k9w7-tar.default for
an 1130 series access point, c1240-k9w7-tar.default for
a 1240 series access point, and c1250-k9w7-tar.default for
a 1250 series access point.
Step
6 Connect
the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step
7 Disconnect
power from the access point.
Step
8 Press
and hold MODE while you reconnect power to the access point.
Step
9 Hold
the MODE button until the status LED turns red (approximately 20 to
30 seconds) and then release.
Step
10 Wait
until the access point reboots, as indicated by all LEDs turning green followed
by the Status LED blinking green.
Step
11 After
the access point reboots, reconfigure it using the GUI or the CLI.
Scenario
C3750X –-- CAP-2601I
·
1
vlan 1 SSID
Switch
configuration
switchport
access vlan xxx Just 1 vlan switch will control
switchport
mode access
·
Multiple
vlan & SSID,
Note: If have multiple Vlan/SSID Trunk needed to configure on the
switch port
Switch
configuration
switchport
trunk encapsulation dot1q
switchport
mode trunk
switchport
allowed vlan xx, xx, xx
switchport
trunk native vlan xx Usually the management IP for the AP
Access
Point Configuration
show run
Building
configuration...
dot11
ssid GLBSYM
authentication open
guest-mode
Broscast SSID
!
!
dot11
guest
!
interface
Dot11Radio0 2.4Ghz Radio
no ip
address
!
encryption
key 1 size 128bit 7 6A074B7F357E124C750C1F17280E transmit-key
encryption
mode wep mandatory
!
ssid
GLBSYM
!
stbc
channel
2437
!
interface
Dot11Radio1 5Ghz Radio
no ip
address
!
encryption
key 1 size 128bit 7 6A074B7F357E124C750C1F17280E transmit-key
encryption
mode wep mandatory
!
ssid
GLBSYM
!
stbc
speed
basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8.
m9. m10. m11. m12. m13. m14. m15.
power
local 11
!
interface
GigabitEthernet0
no ip
address
duplex
auto
speed
auto
bridge-group
1
bridge-group
1 spanning-disabled
no
bridge-group 1 source-learning
!
interface
BVI1 bridge virtual interface <- the management IP address
ip
address 10.93.107.220 255.255.255.128
!
ip
default-gateway 10.93.107.129 <- Gateway IP address, normally
point to DHCP server or DHCP relay
all
!
End
